Call an Engineer today on 01732 622990

Contact Us   Book A Job     Follow Us:
Your Heat > Boiler Installations  > Ideal Boiler Fault Code – Explained
Ideal Fault Code

Ideal Boiler Fault Code – Explained

Troubleshooting Guide: The Most Common Ideal Boiler Faults and How to Fix Them


Introduction: Identifying Common Faults in Ideal Boilers

Ideal boilers are renowned for their reliability and efficiency, but even the best systems can occasionally experience faults. This comprehensive guide will explore the most common faults found in Ideal boilers, along with their corresponding fault codes. Discover the causes and potential solutions to get your boiler back up and running smoothly.


Get in touch today on 01732 622990 or CONTACT US


Low Water Pressure – Fault Code: F1

Low water pressure is a frequent issue that can cause your boiler to malfunction. Check for leaks in the system, valves, or radiators, and ensure the filling loop is correctly connected. Increasing the water pressure should resolve this fault.



Ignition Lockout – Fault Code: F2

If your boiler repeatedly encounters an ignition lockout, it may indicate a blocked flue or condensate pipe. Additionally, inspect these components for obstructions, remove any debris, and reset the boiler to rectify the fault.



Flame Loss – Fault Code: F3

A flame loss fault code could indicate a problem with the burner or gas supply. Too, ensure there are no blockages in the burner or pilot light, and check the gas supply for faults. If the issue persists, seek professional assistance.



Overheating – Fault Code: F4

Excessive heat within the boiler system can trigger an overheating fault. And inspect the thermostat and temperature controls, adjusting them if necessary. Moreover, clean the heat exchanger and ensure proper ventilation to resolve the issue.



Fan Failure – Fault Code: F5

The fan failure fault can be caused by a faulty fan or issues with the wiring. Verify that the fan is functioning correctly and free from obstructions. And if needed, replace the fan or consult a professional for guidance.



Flow Temperature Sensor Fault – Fault Code: F6

A flow temperature sensor fault may indicate faulty wiring, damaged sensors, or a faulty circuit board. Inspect the sensor and wiring connections for damage, then tighten loose connections, and replace any faulty components if necessary.



Faulty Pump or Circulation – Fault Code: F7

If the pump or circulation system is faulty, your boiler may display an F7 fault code. In sum, check for pump blockages, leaks, or worn-out parts. If needed, replace the pump or seek professional assistance to resolve the fault.


No water in system – Fault Code L1

Ensure that the main water supply to the boiler is turned on. Also, check for leaks or airlocks in the system and address them accordingly. Moreover, you’ll need to verify that valves, such as the filling loop, are correctly positioned and not closed.


Blocked Condensate Pipe – Fault Code: L2

A blocked condensate pipe can cause a fault code L2. Inspect the pipe for obstructions, such as frozen condensate. Thaw the pipe using warm water or a hot water bottle, and ensure it is clear and functional.



Sensor Failure or Thermistor Issues – Fault Code: L3

An L3 fault code suggests a sensor failure or thermistor issue. Check the connections and wiring for damage, ensuring they are securely connected. If the fault persists, consider replacing the affected component.


Cross Open Thermostat or Wiring Fault – Fault Code: L4

A wiring fault or a cross open thermostat can trigger an L4 fault code. Inspect the wiring connections for damage or loose connections and replace any faulty parts as necessary.


Combustion System Fault – Fault Code: L9

A combustion system fault code L9 could indicate issues with the gas supply, burner, or ignition system. Inspect these components for any obstructions or blocked pipes. However a professional assistance may be required if the issue persists.


Summary and Conclusion: Resolving Ideal Boiler Faults

While encountering faults in your Ideal boiler can be frustrating, most issues can be resolved with simple troubleshooting steps. Consequently, by knowing the common fault codes and their corresponding causes, you can effectively identify and address problems in your boiler system. However, for complex or persistent faults, it is advisable to seek professional assistance to ensure a safe and accurate diagnosis and resolution.


Get in touch today on 01732 622990 or CONTACT US


Tom Hewitt
No Comments

Leave a reply

× Chat with us!